English
DeutschExpert Aux App
The Expert Aux App will allow you to get access to 13 free-programmable makro cells inside the VBar of your model.
As it is a "real" Expert App every user must take care for his own programming to avoid unintendend overwriting of already programmed cells like for nitro governor, landing flaps or used cells from the Pro Aux App (if in use).
We recommend to copy the current model setup on your VBar Control before starting with this app. So you would be able to restore it back to the model very easy if needed. It will be also very helpful to test the output signals first with a seperate, not built in servo on the bench - this may avoid surprises in flight later.
The VBar can handle up to 5 cells as direct output cells or as control cells - and up to 8 additional cells as control cells only. Please have a look about the cells, assignment and possible pre-definitions at the table below.
The input values for all makro cells can be all potis, sticks, switches, VBar servo outputs (K1-KT) and of course other Makro cells.
The Makro cells can be chained, so we can realize complex controls too. Each Makro cell can be used for another one as input value.
In the plane version the output of cell #5 is shown as flap input on all wing mixers. We use this e.g. for the landing flap functionality.
The Makro cell setup will be stored in the VBar. The app here is only needed for setup - but not for later usage.
Our failsafe positions are adjustable and stored in the VBar too. For a failsafe check - just disconnect the rx satellite from the VBar.
| Makrocells for helicopters - list of pre-defined cells | |||
|---|---|---|---|
| Cell | Output | Pro Aux** | Nitro** |
| 1 | Rudder* | Rudder - Output cell | Switchglow - Combined cell |
| 2 | Elevator* | Elevator - Output cell | |
| 3 | Ch4*** | ||
| 4 | Servo*** | Servo - Output cell | Throttle servo - Output cell |
| 5 | Aileron*** | Aileron - Output cell | |
| 6 | no output | ||
| 7 | no output | Servo - Control cell | |
| 8 | no output | Elevator - Control cell | |
| 9 | no output | Aileron - Control cell | |
| 10 | no output | Rudder - Control cell | |
| 11 | no output | Throttle servo - Control cell | |
| 12 | no output | Throttle servo - Control cell | |
| 13 | no output | Throttle servo - Control cell | |
* On a VBar Mini we have only 2 outputs. RXA center pin is Cell 2 (Elevator) signal, RXA lower pin is Cell 1 (Rudder)
** App / Configuration not available on a VBar Mini
*** Output not available on a VBar Mini - cell is a "no Output" cell there.
| Makrocells for planes - list of pre-defined cells | |||
|---|---|---|---|
| Cell | Output | Pro Aux** | Landing Flaps** |
| 1 | Elevator* | Elevator - Output cell | |
| 2 | no output | ||
| 3 | Aileron*** | Aileron - Output cell | |
| 4 | Rudder* | Rudder - Output cell | |
| 5 | Flap Mix | Output to wing mixers | Landing flaps - Control cell |
| 6 | no output | Landing flaps - Control cell | |
| 7 | no output | Rudder - Control cell | |
| 8 | no output | ||
| 9 | no output | Aileron - Control cell | |
| 10 | no output | Elevator - Control cell | |
| 11 | no output | ||
| 12 | no output | ||
| 13 | no output | ||
* On a VPlane Mini we have only 2 outputs. RXA center pin is Cell 1 (Elevator) signal, RXA lower pin is Cell 4 (Rudder)
** App / Configuration not available on a VPlane Mini
*** Output not available on a VPlane Mini - cell is a "no Output" cell there.
For more information to each cell type - please click on the linked articles below.